Parallel Data Cable (Printer extension cable, with male-female 25 pin connector, and pin to pin through)	A-A type USB cable(for power)



ATMEL89 Adapter	ATMEL PLCC 44 Adapter	TSOP 48 Adapter

FWH/HUB PLCC32Adapter	PLCC32 Adapter	SOIC Adapter(Simplified)
On-Board	On-Board
AC or DC Power Adapter (9V or 12V, 200mA)	SOIC Adapter(Professional)	
		

War For The Overworld Ultimate Edition-plaza -

The "Ultimate Edition" of (specifically the version from the PLAZA release) is a comprehensive bundle that combines the base game with every major expansion and piece of bonus content. Key Included Content

: Includes the Sovereign Dungeon Theme , the full digital soundtrack, a 48-page lore book, and short story compilations. Notable Gameplay Features War For The Overworld Ultimate Edition-PLAZA

: A survival mode that pits you against an endless wave of enemies to see how long your dungeon can hold out. The "Ultimate Edition" of (specifically the version from

: An eight-level "chilled-out" campaign focused on exploration and sandbox building rather than high-stakes combat. the full digital soundtrack

: A narrative campaign where you play as the gold-obsessed Underlord Kasita across four new levels.

: A seven-level skirmish tournament where you choose from Underlords with unique playstyles to compete in knockout-style matches.

Installation Steps


Check the parallel printer port setting in the bios, it should be EPP or Normal.
Check there are any active resident programs that use the printer port, such as TWAIN drivers. You may have to remove it.
Connect one end of the 25 pin SubD parallel cable to PCprinter port
Connect the other end of parallel cable to 25Pins port of the programmer
Connect USB power cable or AC adaptor (Note: if you are working on the EPROM programming. You may need use a AC adaptor, so that you can get Vcc 5.6V and 6.2V when doing programming)
Theyellowpower normal indicator of the programmer should light up, then the programmer power supply is normal.
Run the software
Select devices type
Click the Willem in toolbar to change to PCB3
Set the DIP switch based on the displayed pattern.

 (Note: theLPT portof PC MUSTset to ECP or ECP+EPP during BIOS setup. To enter the BIOS setting mode, you need press "Del" key or "F1" key during the computer selftest, which is the moment of computer just power up.)



Software Version To Use

The softwarecan be download fromdownload.mcumall.com

There are board hardware selection jumper on the board. When set the jumper to PCB3B, then user have to use 0.97ja and before version software.

If the board selection set to PCB3.5, PCB5.0, PCB5.5C, then the software 0.98D6 should be used.



 The softwareinterface:



War For The Overworld Ultimate Edition-PLAZA



Hardware Check

After start the program, click test hardwar under Help menu. If the connection and power supply is normal, then appears: "Hardware present" Otherwisecheck if the programmer connects well with PC, or power supply is normal.



Jumper Configuration



PCB3.5/PCB4E

War For The Overworld Ultimate Edition-PLAZA 
(Two PLCC32 adapter is not applied on the PCB4E)



PCB5.0

War For The Overworld Ultimate Edition-PLAZA



PCB5.5C



War For The Overworld Ultimate Edition-PLAZA

Note: the Vcc setting jumper only has effect when you are using AC adaptor as power source. For the USB power only 5V Vcc is available.

For the PCB5.5C, set DIP steps:

1. press DIP Set button twice to check current DIP bit position. Then set it again for ON or OFF.

2. press DIP Bit shift button to shift the DIP bit position to where need to set. And then press DIP Set button twice to check current DIP bit position. Then set it again for ON or OFF.

3. Repeat those steps till all DIP bit ae set same as software indicated.

For PCB5.5C voltage and Special chip selection:

1. Put back the safety jumper.

2. Press the voltage button and hold for 1 second, the voltage LED should move to next. Repeat till desired voltage LED light up.

3. Press the chip selectionbutton and hold for 1 second, the chip LED should move to next. Repeat till desiredLED light up.

4. Remove the safety jumper to lock the selected voltage and chip selection



DIPSwitch (PCB3.5, PCB5.0)

War For The Overworld Ultimate Edition-PLAZA 

When programming one chip, followthe program prompt to set DIP switch.



: Includes the Sovereign Dungeon Theme , the full digital soundtrack, a 48-page lore book, and short story compilations. Notable Gameplay Features

: A survival mode that pits you against an endless wave of enemies to see how long your dungeon can hold out.

: An eight-level "chilled-out" campaign focused on exploration and sandbox building rather than high-stakes combat.

: A narrative campaign where you play as the gold-obsessed Underlord Kasita across four new levels.

: A seven-level skirmish tournament where you choose from Underlords with unique playstyles to compete in knockout-style matches.